These models are tough and built to take the weight and abuse
Fold Down Saddle Rack Model CM 40
• Constructed of heavy 3/4" tubing and 1 1/4 flat bar - all assembled into a single unit.
• Extends out 24 inches in the upright position and lays flat against the wall in the down position.
• An integral bridle hook is included that can be used in either position.
• Three mounting bolt holes are provided to give complete stability.
• Enamel coated for rust prevention.
$42.00
Questions? Call us at 800-335-1880!
Western Saddle Rack Model CM 41
Western Saddle Racks are constructed of 1/2 inch round hot rolled steel. Welded into one piece, these models are designed for quick removal and portability. Use any place where you can install a single eye bolt (tack room, trailer, single post). The units can also be laid flat against the wall.
$36.00
English Saddle Rack Model CM 42
English Saddle Racks are constructed of 1/2 inch round hot rolled steel. Welded into one piece, these models are designed for quick removal and portability. Use any place where you can install a single eye bolt (tack room, trailer, single post). The units can also be laid flat against the wall.
$36.00
Only one eye bolt required for mounting (on Model CM 41 & CM 42 only)
Saddle Racks and Saddle Stands
Horse Stall Accessories
Horse Water Bucket Holders
Bucket Holders - Model CM 912
Completely eliminates torn out handles and deformed buckets.
Mount this high strength all steel holder on the wall and set your bucket within.
Allows use of inexpensive buckets.
Constructed of 1/2" hot rolled steel welded to 1 1/4" wide mounting plates. Four holes are provided for rigid mounting.
This BUCKET HOLDER will hold both the 5 gallon poly buckets and the smaller rubber buckets. Inside dimensions are 13" width x 12.5" x 12" high. (color black)
$42.00
Questions? Call us at 800-335-1880!
Bridle Racks & Blanket Bars
Curved Bridle Rack - Model CM 65
Designed for convenience and uniform support of those special bridles and tack. Six curved holders with a front lip are welded to a 48" single piece mounting bar (3 mounting holes). Great for tack rooms & trailers. Enamel coated for corrosion protection.
$31.00
Hooked Bridle Rack - Model CM 66
This versatile 48" steel bridle rack contains six hook type holders, each 4" high by 3" deep. Many uses include: all type of tack equipment, clothes, hats, barn chore equipment, etc.
$31.00
Folding Blanket Bar Model CM44
This folding blanket bar is great for barn aisles with limited space. The blanket area measures 38 inches wide and requires 42 inches on your stall door for the mounting brackets. The bar extends 7 inches out from the door surface and folds down to 1 3/4 inches from the door surface. All steel construction for strength with wet saddle blankets. Enamel coated black for corrosion protection.
$48.00
Questions? Call us at 800-335-1880!
Horse Stall Cross Ties
Cross Ties - Model CM 68
Rugged, 3 1/2" X 4" steel mounting plate provides the extra strength needed to insure safety. Four mounting holes are provided. A 3/8 inch hot rolled steel ring, butt welded to prevent separation, is hinged beneath the heavily welded support loop. The 2 inch 1. D. steel ring allows use of almost any type of tie rope. Two per package.
$25.00
Horse Stall Gravity Latch
Gravity Latch - Model CM 2
Latches against stay roller side of door
Can be positioned for hand or foot operation
Safer than sliding latches
Horses can't get caught upon stall entry
Works with most sliding doors
Great for children working around the stalls. When the stall door closes, the latch automatically falls and locks the door shut!
$18.00
Questions? Call us at 800-335-1880!
Gravity Latch Installation Video
CM 3 Bottom Door Catch
Required on doors, using the gravity latch, if not already equipped with another hold in device. Prevents the horse from pushing out the bottom of the door.
High Strength - Swinging Saddle Blanket Rack. Steel Construction with Black Enamel Coating. Strong enough to hold heavy, wet blankets and saddle pads. 3 Swinging Arms allow to position them independently . Four point mounting for stability. Each arm can be removed easily. Mounting surface is 24 inches. Arm length is 31 inches. Weight approximately 7 lbs. You are buying factory direct. MADE IN USA
