Horsestalls.com
Factory Direct Sales 800-335-1880
Horse Feeders and Watering Units for Horse Stalls 
Imagine how much time you would save being able to Hay, Grain, and Water your horse without having to enter the stall. Our swing out combination feeder and utility door units can upgrade your horse stall system appearance and versatility at minimal cost and effort.
Save tons of time and labor with our uniquely designed swing out utility door. Made of heavy duty 1/8" steel plate mounted on a sturdy angle iron frame. Measures 22" H x 20" W. Designed to accommodate a wide variety of feeders, buckets, bucket holders, or our Thermo Bucket. Heavy duty latch is designed so that the door cannot be opened from the inside. Can be installed to swing out from the left or right by simply inverting the frame.
Steel Swing Out Utility Door. Model CM 122
(Door shown with mounted Thermo Bucket not included) Paint color black. Questions? Call 800-335-1880
Black Painted Steel Thermo-Bucket Model TB-1
Keeps your horse’s water from freezing for 6-12 hours without electricity!
(Shown with Utility Door not included) Paint color black.
Swing Out Combination Feeders
The feeder is pivoted on a sturdy angle iron frame that is symmetrically designed so it can be used on either the left or right hand side of the stall by simply inverting the frame. The feeder is constructed of heavy duty 16 gauge hot rolled steel with a removable polyethylene feed pan and 1/4" rod trimming on all exposed edges to eliminate sharp edges. The internal hay rack is welded 7/16" hot rolled steel rod. Measures 37" H x 22" W.
Steel Swing Out Combination Feeder
Model CM 121 (Paint color black)
Thermo Buckets. Keeps your water from freezing WITHOUT electricity!
Questions? Call us at 1-800-335-1880
Wall Model Hay Rack Model CM 212.
• Top opening is 2 feet wide x 1 foot deep. Unit is 2 feet high.
• Open space between bars for safety.
• Four corner mounting for rigidity.
• All steel welded construction using 7/16" hot rolled steel. (color black)
Corner Model Hay Rack Model CM 213
Maximize stall Space with this heavy duty Hay Rack
• Rugged welded construction
• All steel welded construction using 7/16" hot rolled steel.
• Big 30 inch opening at top, tapered to 16 inches at bottom. (color black).
Combination Feeder Model CM 2125.
One feeder for both jobs - hay and grain
• For the corral or stall.
• Hang onto your fence or trailer, or mount on your stall wall.
• 2 ft. wide x 1 ft. deep x 2 1/2 ft. high. Holds a bunch of hay and 5 gallons of grain.
• No wasted hay! Falls into tray.
• Rugged 16 gauge steel with heavy steel hay bars.
• Removable hangers are made to withstand the punishment of horses.
Rugged Cast Aluminum Horse Grain Feeders High Strength - No Corrosion Lifetime Horse Feeders
Extremely heavy duty cast aluminum provides the toughest structure, yet is light in weight. You get both the advantages of plastic (corrosion prevention) and steel (high strength) with cast aluminum. With horses and other live stock, RUGGED CONSTRUCTION is a must. Both feeders have spherical shaped bottoms which causes the feed to flow to a single low point allowing easy clean up by the animal. If you have grown tired of constantly replacing the rubber and plastic feeders, here is the one-time solution!
• Each mounting surface is 16 in. long with a depth of 6 in.
• Weight approximately 11 lbs.
• Three point mounting for stability
• 20 in. wide at rear x 6 in. deep x 12 in. front to back.
• Weight approximately 13 lbs.
CM 34L Feed Saver Lid for Corner Feeders
Cast feeder shown NOT included
Stops the annoying and the wasteful habit some horses have of slinging their grain out of the feeder and onto the floor! The center opening is 5 3/4" wide. The steel bars are welded in place onto the heavy steel frame. Each Feed Saver Lid comes with 2 hold down brackets to attach to the feeder mounting hardware, but allows for easy cleaning. Designed to fit our cast aluminum corner feeders only.
CM 33L Feed Saver Lid for Wall Feeders
Cast feeder shown NOT included
Stops the annoying and the wasteful habit some horses have of slinging their grain out of the feeder and onto the floor! The center opening is 6" wide. The steel bars are welded in place onto the heavy steel frame. Each Feed Saver Lid comes with 2 hold down brackets to attach to the feeder mounting hardware, but allows for easy cleaning. Designed to fit our cast aluminum wall feeders only.